卷帘门遥控器的配对方法因类型不同而有所差异，以下是常见的几种配对方式：

The pairing methods for remote control of rolling shutter doors vary depending on the type. The following are common pairing methods:

学习型遥控器配对

Pairing of Learning Remote Control

准备工作：确保卷帘门电源已开启且处于待机状态，检查遥控器电池电量充足，确认遥控器与卷帘门型号匹配。

Preparation: Ensure that the power supply of the rolling shutter door is turned on and in standby mode, check that the remote control battery is fully charged, and confirm that the remote control matches the rolling shutter door model.

进入控制器学习模式：使用螺丝刀打开卷帘门控制器的外壳，找到主板上的学习按钮（通常标记为 “Learn” 或 “学习”）。按下并保持该按钮几秒钟，直到指示灯开始闪烁，表示控制器进入学习模式，部分控制器通过按下学习按钮后会发出声音提示进入学习模式。

Enter controller learning mode: Use a screwdriver to open the housing of the rolling shutter door controller and locate the learning button on the motherboard (usually labeled as "Learn" or "Learn"). Press and hold the button for a few seconds until the indicator light starts flashing, indicating that the controller has entered learning mode. Some controllers will emit a sound prompt to enter learning mode by pressing the learning button.

同步遥控器：在控制器处于学习模式时，按下遥控器上的任意按键（通常是开门键），等待几秒钟，确保控制器识别遥控器信号。

Synchronous remote control: When the controller is in learning mode, press any button on the remote control (usually the door open button) and wait for a few seconds to ensure that the controller recognizes the remote control signal.

完成配对：指示灯停止闪烁或发出确认声，表示配对成功。

Pairing completed: The indicator light stops flashing or makes a confirmation sound, indicating successful pairing.

测试：关闭控制器外壳，按下遥控器上的按键测试卷帘门的开启和关闭功能。

Test: Close the controller casing and press the button on the remote control to test the opening and closing function of the rolling shutter door.

拨码型遥控器配对

Dial type remote control pairing

清码：卷帘门遥控器接收模块上面一般有一个白色或者黑色的按键，即学习键。在通电的情况下，按下这个学习键，此时学习键旁的学习指示灯亮起，等它闪两下熄灭之后，松开手，清码成功。

Clear code: There is usually a white or black button on the receiving module of the rolling shutter door remote control, which is the learning button. When powered on, press this learning button. The learning indicator light next to the learning button will light up. After it flashes twice and goes out, release your hand and clear the code successfully.

对码：清码成功后，再次按下学习键，此时学习指示灯亮起，然后按下手柄上面的按键，此时学习指示灯会闪 5 下，接着熄灭，表明卷帘门遥控器对码成功。

Code pairing: After successfully clearing the code, press the learning button again, and the learning indicator light will turn on. Then press the button on the handle, and the learning indicator light will flash 5 times and then turn off, indicating that the remote control for the rolling shutter door has successfully aligned the code.

对拷型遥控器配对

Pairing of Copy type Remote Control

清码：一般是双手同时按遥控器锁键和下行键，这时指示灯会不停闪动，再松开双手。然后随便按一个键，遥控器指示灯亮一下就熄灭，表示清码成功。

Clear code: Generally, both hands press the lock button and down button on the remote control at the same time. At this time, the indicator light will flash continuously, and then release both hands. Then press any key and the remote control indicator light will turn on and then turn off, indicating successful code clearing.

对拷：拿出需要配对的新遥控器与原遥控器，两个遥控器对准，双手同时按住两个遥控器的开门键，指示灯快速闪动即为成功。

Copy: Take out the new remote control that needs to be paired with the original remote control, align the two remote controls, hold down the door opening buttons of both remote controls with both hands, and the indicator light flashes quickly to indicate success.

其他按键拷贝：其他按键如关门键、停止键、锁键等的拷贝方法与开门键相同，依次进行即可。

Copy other buttons: The copying method for other buttons such as the door close button, stop button, lock button, etc. is the same as that for the door open button, and can be done sequentially.

智能 App 配对

Intelligent App Matching

下载应用程序：根据卷帘门的品牌，在手机应用商店下载相应的手机应用程序。

Download the application: Depending on the brand of the rolling shutter door, download the corresponding mobile application from the mobile app store.

注册并登录账号：打开应用程序，按照提示进行用户注册并登录。

Register and log in account: Open the application, fol