铁艺大门固然好看，固然结实，固然很。但是如果表面处理不好，时间长铁艺大门表面就会上锈，那么如何保持铁艺大门的表面美观度呢，如何处理铁艺大门的表面呢？下面我给大家介绍一下：

The wrought iron gate is certainly beautiful, sturdy, and noble. But if the surface treatment is not good, the surface of the wrought iron gate will rust over time. So how to maintain the aesthetic appearance of the wrought iron gate and how to treat the surface of the wrought iron gate? Below, I will introduce to you:

铁艺大门材料坚固，类型多种多样.风格各异，而且庄重、豪华。铁艺大门的颜色一般有黑色和古铜色。铁艺大门用的材料有方管、锻打方管、方钢、矩形管、锻打矩形管、锻打方钢、圆钢、扁铁、锻打扁铁、铁板、玛钢件、冲压件、门轴等。

The iron gate material is sturdy, with a variety of types and styles, and is solemn and luxurious. The colors of wrought iron gates are generally black and bronze. The materials used for wrought iron gates include square tubes, forged square tubes, square steel, rectangular tubes, forged rectangular tubes, forged square steel, round steel, flat iron, forged flat iron, iron plates, Ma steel parts, stamped parts, door shafts, etc.

一、焊渣 大门的焊接部位较多，必须认真每个焊接部位的焊渣。先用板锉或扁铁敲打除渣，然后用磨光机和砂布打磨焊缝，使其平滑。对飞溅到其他部位的焊渣也要顺势干净。

1、 There are many welding parts of the gate for removing welding slag, and it is necessary to carefully remove the welding slag from each welding part. First, use a board file or flat iron to remove slag, and then use a polishing machine and sandpaper to polish the weld seam to make it smooth. The welding slag that splashes onto other parts should also be cleaned up in a timely manner.

二、涂抹原子灰 用原子灰加固化剂(比例50:1)搅拌均匀，涂抹在焊接部位.处理焊缝缺陷。

2、 Apply atomic ash with a curing agent (50:1 ratio) and stir evenly. Apply it to the welding area to treat weld defects.

三、打磨原子灰 干透后，用磨光机和砂布打磨大门的各个组件，尤其是涂抹原子灰的部位更要磨光。

3、 After the atomic ash is completely dried, use a polishing machine and sanding cloth to thoroughly polish all components of the gate, especially the parts coated with atomic ash.

四、喷漆 喷漆前，用湿布擦净大门的各个部位，不能留有灰尘等。道喷防锈漆，漆膜干透后喷第二道黑漆，喷一道清漆。注意不能有漏喷部位，也不能产生流挂等缺陷。个别细微处可用刷子刷涂补漆。

4、 Before painting, use a damp cloth to thoroughly clean all parts of the door without leaving any dust or debris. The first coat is anti rust paint, the second coat is black paint after the paint film is dry, and the last coat is clear paint. Be careful not to have any areas of leakage or defects such as sagging. Individual small details can be brushed and repainted with a brush.